Skip to main content
G
guido22727016jqli
Participant
January 19, 2022
Question

Audition CC MME device internal error

  • January 19, 2022
  • 1 reply
  • 1945 views

hallo

I have desktop pc 2009 with gigabyte motherboard EP43  and onboard audio  but all runs  well,audition or ANY other trial of a daw worked well RECORDING sound on win7 64 bit, but nothing possible on win10 or win 11

been trying for 3 weeks,

solution  ? ???  put NO input makes that I can  not record sound,either from a file on the desktop, or from a cassettedeck, there is NO  microphone on this pc nor attached

in the NO input suggestion I can open a sound file and  play it, I can not record in this case,logically if there is no input ,no stereomix,no line in  then no signal in the output

 

 

solution ? ???privacy security allow  microphone access ON and allow apps to use microphone ON

yes then  there is no MME I can record BUT immediately a very severe reverb almost echo appears

I work with professional headphones so as there is no microphone there must in this case  be a feedback in the system

 

choosing wasapi or asio no difference 

 

so no  solutions these socalled solutions       

I have tried many trial versions of older auditions  as far back as audition 1.5 ,but same problems on a daw like soundforge                                    NO such problems on windows 7 64 bit

I only  have trials that I  picked up  online to test them   but I do have cooledit 2.1 that I bought from syndtrillium long time ago,works ok on win7

 

guido from belgium europe  70 years old,I am reasonably good in computers but no expert,but experts often disappoint me  !!!! they know much less than I expected,

 

[Mod note: Moved to a thread of its own]

This topic has been closed for replies.

1 reply

SteveG_AudioMasters_
Community Expert
SteveG_AudioMasters_Community Expert
Community Expert
January 19, 2022

I'm not surprised that you have feedback - you are trying to record using the 'Stereo Mix' setting, rather than the mic input directly. If you use Stereo Mix, then everything else happening will get fed back - with a latency delay - to your recorded input where it will promptly be re-recorded.

 

So you need to alter the Windows record settings so that it's only the mic (or whatever is plugged into whatever input you have) gets recorded.

G
guido22727016jqliAuthor
Participant
January 19, 2022

Dear Mister Steve

 

thank you for your speedy reply

 

 

1 no reverb feedback on win7 and in this case all well directly with  line in  and ----stereomix----

 

 

2  of course I also tried line in default 

 

see printscreens

 

can not record,same problem   !!

 

thank you for your patience, 

G
guido22727016jqliAuthor
Participant
January 19, 2022

You should look at the line in Properties and make sure that the input configuration is set the same as the Audition input configuration for recording. So they should both be set to either 44.1k or 48k. If you don't do that, you will very likely not be able to record (which is probably why it says 'unavailable'). You may also like to try taking the check out of  'Use Machine-specific Device Defaults' - that could also cause a conflict.


Dear Sir

I have macrium reflect backups for win7 ,10 ,11

so in 7 minutes I can switch between systems 

 

I now made the same  recordings with an older audition  CC 2015 trial because I cannot install the latest on win7,is only for win10 and 11

but recordings NO problem both in stereomix and line in 

perfect  ,so why here no signal feedback leading to reverb and even echos 

I again connected my cassettedeck and tried both either stereomix and line in  and in both cases I hear the cassette sound on my hearphones and is visible in audition cc 2015 and recording nicely

 

this material is difficult to understand because I as a  simple man and not a sound engineer do not understand the diagram switching inside the chips

with a  normal mixing apparatus of the older days this is easier to understand,signals  coming in from various sources,mixers with preamps, those I understand because I was a simple electronics amateur fooling around in my little lab with the various tools of the trade,not commercial but just for my own fun all this 1990

 

so if  I post all this I also do this so that others might learn,question the problem and  perhaps help me my poor soul

I can of course always revert to win7,the recordings I do from my revox B77 recorder and cassette deck are only family member recordings,people long dead

not music, so digitizing them is almost done, 95% but it should also work on win 10 and 11 for the present generation

 

and the same problem with a trial of soundforge    ,on win10  and 11 same problems, not on win7

so it is not adobe product,it is the OS made by mister rich bill gates 

 

I bought win7 for 25 dollars from an american on ebay for 20 dollar in 2009, last year only I updated to win10  pro all for free, and updated to win11 pro all for free

so this is on the cheap and not stolen software by the way  !!!!!!!!

and have been making backups with macrium reflect to freeze them in time

Terms & ConditionsAccessibility statement
Using the community Terms of use Privacy Cookie preferences Do not sell or share my personal information ad choicesAdChoices