Skip to main content
A
Anonymous
October 16, 2021
Answered

Doubling Image Size

  • October 16, 2021
  • 3 replies
  • 2222 views

I'm pretty sure I know the answer to this question. Just want to be sure.

 

  1. I have an 8x10 photo at 300dpi in photoshop. 
  2. I double the size by percentage to 200% which equals a 16x20.
  3. It still says 300dpi.
  4. Technically however, the 16x20 will print at 150 dpi (dots per inch)
  5. Is this correct?
This topic has been closed for replies.
Correct answer TheDigitalDog
@21272449 wrote:

Thank you both @Myra Ferguson and @gener7 for your help.

However I would assume if I resampled the 8x10 300dpi image up to 16x20 at 300 dpi the quality of a printed photograph would still be somewhat considerably worse?

Yes, you're creating 'data' out of thin air. 

Depending on the output device (and viewing distance as discussed), you can easily get away with 180-200PPI (DPI if you will). So just turn OFF the resample check box (you don't want to add or remove pixels), entire 20 inches on the long dimension. That gets close (150 PPI instead without any resampling), maybe consider now, resampling less, to 180PPI, again depending on the type of output device. 

There is absolutely nothing special about "300dpi" resolution for anything. Digital imaging urban legend that needs to die. 

3 replies

jane-e
Community Expert
jane-eCommunity Expert
Community Expert
October 17, 2021
@21272449 wrote:
  1. Technically however, the 16x20 will print at 150 dpi (dots per inch)

 

Technically? The dots of ink per inch (dpi) depends on the printing device.

https://www.adorama.com/alc/dpi-vs-ppi-whats-the-difference/

 

~ Jane

 

    D Fosse
    Community Expert
    D FosseCommunity Expert
    Community Expert
    October 17, 2021

    Right. Maybe it's time to clean up the concepts.

     

    Photoshop only works with pixels. The file is just pixels. Physical print size is determined later by assigning a pixels per inch number. This simple formula is used to translate from pixels into a physical size on paper.

     

    Say it out loud three times: pixels per inch. It means exactly what it says. These three words are the key to the whole thing. Ppi is not a native property of the file. It's just a standard equation, and like any equation, it can be shuffled around and stood on its head: knowing two values, you can always calculate the third.

     

    Dots per inch is something else. That's the printer, how many dots of ink it will lay out per inch. You can use any random number of dots to print one pixel. These two are not connected!

     

    Pixels per inch is the image.

     

    Dots per inch is the printer.

      gener7
      Community Expert
      gener7Community Expert
      Community Expert
      October 16, 2021

      If you have Resample checked, Photoshop doubles the pixels so you can keep that resolution of 300 ppi.

       

      If you uncheck Resample then Photoshop leaves the pixels as is and the resolution goes to 150 ppi

        JJMack
        Community Expert
        JJMackCommunity Expert
        Community Expert
        October 17, 2021

        Actually doubling the size width and height is 4 times the number of Pixels. Where 300% would be 9 times Pixels soon the canvas size becomes huge and Photoshop performance go to pot.  While the image quality degrades and become a softer blurred image.  If you are printing a mural on a building in sections the image lay look less jagged  degraded promted ar a higher resolution than boxy printed as a supper low resolution

        JJMack
        Myra Ferguson
        Community Expert
        Myra FergusonCommunity Expert
        Community Expert
        October 16, 2021

        If you go to Image > Image Size and adjust the size in the Width and Height, you'll notice a difference in the file size when you select or deselect Resample.

        • If Resample is selected, you can choose Automatic or one of the two enlargement algorithms to increase the image so that the result would be 16x20 at 300 ppi.
        • Otherwise, if Resample is deselected, then the result would be 16x20 at 150 ppi.
          A
          Anonymous
          October 17, 2021

          Thank you both @Myra Ferguson and @gener7 for your help.

          However I would assume if I resampled the 8x10 300dpi image up to 16x20 at 300 dpi the quality of a printed photograph would still be somewhat considerably worse?

          D Fosse
          Community Expert
          D FosseCommunity Expert
          Community Expert
          October 17, 2021

          Upsampling is always a question of minimizing the damage. It will never, ever, improve anything and you will get a better visual result by printing the file as-is.

           

          It is only justified when there is a real risk of visible pixels. You don't need to upsample just because it's being printed large.

           

          That said, the best results are potentially achieved by using the "super resolution" function in ACR/Lightroom on raw files. It uses ai-algorithms to reduce artifacts.

            Terms & ConditionsAccessibility statement
            Using the community Terms of use Privacy Cookie preferences Do not sell or share my personal information ad choicesAdChoices