Skip to main content
Claudio González
Legend
Mar 16, 2008 2:40 AM UTC
Question

Slow, slow, slow (III) !

The thread with this name that was closed with no explanation did serve a useful purpose, so I am opening a new one to replace it.

Speed is back to normal now, and if there was a shutdown, I wasn't here to witness it.
    This topic is closed to new replies. Start a new post to keep the conversation going.

    574 replies

    PJonesCET
    Participating Frequently
    May 23, 2008 10:48 PM UTC
    Hell No!

    I can't even get into the system now with out doing a work around and signing in every time!

    To say I am Pixxed is putting it mildly!

    every time I get an announcement in email the link starts with

    http://adobe-eq.webcrossing.com/

    to get in I have to remove the -eq and hit link again then sign in for every massage.

    I am not a Happy camper!

    Same shXX I went through when they had the last fiasco. Turns out someone accidently miss typed a alias link.
    Translate
    May 23, 2008 3:32 PM UTC
    pjones? are you still there?!! :)
    Translate
    PJonesCET
    Participating Frequently
    May 22, 2008 4:06 PM UTC
    You mean slowndowns on your computer. ;-)
    Or a slowdown on Complaints. ;-)
    Translate
    Kath-H
    Inspiring
    May 22, 2008 5:14 AM UTC
    Probably everyone else will be fine and I'll start getting the slowdowns ;)
    Translate
    Known Participant
    May 22, 2008 12:33 AM UTC
    PJ,
    >I find the crimp connections of the Plugs to the sometimes get loose. or the contact get dirty.

    Buy better category 5e or 6 cables with molded ends and keep your work environment free of dust, dirt, and moisture. Maybe even cables with gold-plated contacts to keep corrosion down. And stop tugging/snagging on the cables. Use the shortest cables that comfortably reach from component A to component B.

    ===

    All that said...let's see what happens with speed/connectivity after Forum maintenance tomorrow.

    Neil
    Translate
    ~graffiti
    Legend
    May 22, 2008 12:18 AM UTC
    I'm still trying to remember the last time I replaced a cable...
    Translate
    Known Participant
    May 22, 2008 12:13 AM UTC
    A static curvature won't hurt cables.

    Repeated flexion will.

    Bend a paperclip once. No harm done.

    Bend it back & forth 150 times, and it'll break.

    If you're concerned about the strain, look into some cable wrangling accessories designed to keep relieve strain and keep them in place.

    It's a cheaper, smarter, better solution.
    Translate
    PJonesCET
    Participating Frequently
    May 21, 2008 11:10 PM UTC
    PS I also notice from the announcement above. perhaps they are getting ready to replace the "Hamster". ;-)

    Maybe they have finally after a year figured out what is causing the system being so unreliable.
    Translate
    PJonesCET
    Participating Frequently
    May 21, 2008 11:07 PM UTC
    I find the crimp connections of the Plugs to the sometimes get loose. or the contact get dirty.

    So why keep cords that could possibly cause problems. I've had cables to be the cause of problems.

    Because of My Computer Desk in which the shelves are stacked. everything is not on one level so the connection in the the Plugs Droop. So they receive constant strain.
    Translate
    Known Participant
    May 21, 2008 8:11 PM UTC
    PJ,

    BTW, you should be using category 5e or 6 cables; not the old standard category 5 for your home network. (I assume that is what you meant by "Cat%".)

    There is absolutely no reason to replace properly installed cables every few months unless you are damaging them. They don't wear out. If they are damaged, reroute them so they don't get damaged, or improve your work habits.

    I bought high-quality cables for my LAN a few years ago, and they're still like new.

    Neil
    Translate