Copy link to clipboard
Copied
Hey guys,
here you can see my sketch:
I want to make the circle bigger by draging it. I want to make it exactly that big, so that the circle intercepts with the end of the orange line, like the following sektch would show:
I did this sektch by changing the width [px] and height [px] values. But i do not want it like that. I want it to scale up by dragging. The problem: After making the circle bigger by dragging the outer ring of the circle, the position of the center of the circle changes. It does not stay at the same place. Is there any to do this?
Of course i could just change the height values, but i want the circle to overlap with the end of the line EXACTLY.
Greetings Spedex
If you like you can, of course, duplicate the line segment, use the copy for the rotation, and delete when you have scaled the circle.
Peter
Hi, Jacob, Carlos, and Kurt!
Another way is drawing a temporary guide (dotted line) from the centre of the circle to the top of the vertical line.
Then – while smart guides are turned on – just select the circle, take the Scale tool, start dragging at point A (intersection of circle and dotted line) until you reach point B (upper point of the vertical line).
Copy link to clipboard
Copied
hold the Alt key to keep the center fixed while dragging
Copy link to clipboard
Copied
Spedex,
Smart Guides being your friends you can Select the circle, switch to the Scale Tool, Click somewhere on the upper right of the perimeter and ClickDrag to snap to the top Anchor Point, and while you stay within snapping distance press and hold Shift until you have let go of the mouse button.
Hi Carlos.
Copy link to clipboard
Copied
Hi Jacob!
Copy link to clipboard
Copied
Are you sure that this will really work in this case, Jacob?
Copy link to clipboard
Copied
Hardly, when you are asking, Kurt.
Copy link to clipboard
Copied
If you like you can, of course, duplicate the line segment, use the copy for the rotation, and delete when you have scaled the circle.
Peter
Hi, Jacob, Carlos, and Kurt!
Copy link to clipboard
Copied
Genius!!
hi Peter!
Copy link to clipboard
Copied
Thanks, Carlos. My main source of projects is mostly shut down, so I actually have time to think about stuff.
Copy link to clipboard
Copied
Wow, thats awesome.
Thank you very much for your help.
Copy link to clipboard
Copied
If that works for you I'm delighted. You are very welcome.
Peter
Copy link to clipboard
Copied
Hi Peter.
No show this (non) winter there either?
Copy link to clipboard
Copied
More winter than in decades, slowly vanishing.
Copy link to clipboard
Copied
Another way is drawing a temporary guide (dotted line) from the centre of the circle to the top of the vertical line.
Then – while smart guides are turned on – just select the circle, take the Scale tool, start dragging at point A (intersection of circle and dotted line) until you reach point B (upper point of the vertical line).
Copy link to clipboard
Copied
😉
Why so complicated?
Draw a simple line from circles centerpoint to endpoint of your red line.
This is the radius.
select your circle and set the width = radius * 2
Done and
have fun
😉
Update.
I totally missed Kurt's answer. But as well - one more option.
Copy link to clipboard
Copied
See my last post, but Peters solution is also a good way to do it.
Also, please notice that the initial question was about a way to do it with dragging things instead of doing it the way you are suggesting (which is valuable as well).
Copy link to clipboard
Copied
Nothing wrong with either of those methods; I just wanted to find a way that was all construction/Smart Guides/snapping, and didn't depend on increasingly untrustworthy eyes.
Copy link to clipboard
Copied
Unfortunately, my last post in this thread has been manipulated by someone who has the privilige to do that. Without my agreement.
There was absolutely no insult involved. Just an objective comment.
I hope that this will never happen again. Please do not break the freedom of speech in this forum unless there are bad defamations.