How do I select and move two control handles on two different anchor points so they move concurrently?

[MissSparkles75]

I am drawing a teardrop shape and want to select and move the two ringed control handles upwards at the same time so that the teardrop is exactly the same shape on both sides, is there any way to do this? Thanks.

[Jacob Bugge]

Miss Sparkles,

Just deselect, then Direct Select both path segments (you may ClickDrag across over the Anchor Points with the Handles), then use the Up arrow.

[MissSparkles75]

Hi Jacob,

If I select the two anchor points with my Direct Selection Tool by click dragging, the control handles don't appear (shown below)? The same thing happens if I try to select one anchor point, hold down shift and select the second anchor point.

[c.pfaffenbichler]

Jacob Bugge spoke of the segments themselves, not the bezier handles.

Instead of the arrow keys you could also start draging the segments upwards and hit the shift key to constrain the transformation vertically.

[Jacob Bugge · Accepted solution]

Miss Sparkles,

I apologize for the ambiguity of

over the Anchor Points with the Handles

As c pointed out, the over was meant as above/higher than vertically, rather than covering/including.

ClickDragging across over/above the Anchor Points will select the upper segments and reveal the Handles of the side Anchor Points and the top Anchor Points, but you will only affect the pair of (vertical) upper Handles of the side Anchor Points when you use the Up arrow (just as you will only affect the (horizontal) Handles of the Top Anchor Point if you use Left of Right arrow.

In the image, you have the corresponding lower segments selected with corresponding Handle selection.

[Jacob Bugge]

Miss Sparkles,

You can also select both segments by ShiftClicking each.

And you can extend the Handles by ShiftClickDragging either as c says.

[MissSparkles75]

Thanks Jacob and c.pfaffenbichler, that is excellent, I have wanted to know how to do that for years but never worked it out and could never find the details by googling, THANKS so much.

Thanks SJRiegel, this is the technique I have used in the past but have wanted to know for ages if there was a way to move two control /bezier handles concurrently.

God knows what I'd do without this forum, its awesome. Thanks everyone!

[Jacob Bugge]

For my part you are welcome, Miss Sparkle.

The way Susan (re)told about, which gives a greater freedom in creating the desired shape, can be done live.

Here is the easier way possible with the newer versions, which replaced my earlier suggestion (with an initial preparation) some 4 years ago, and kept among my  snippets:

It is quite possible to create a symmetrical drawing live with the help of Illy, with the inbuilt tools, without any external plugins, if you just start in the right way. Obviously, it is much better to see the whole appearance while you create it.

Depending on the number of reflexion/rotation axes, there are different ways.

For a simple one to two mirroring, you may see the reflection live after each Anchor Point if you start out as follows (for Pen Tool with vertical reflection to the right, similar for other directions):

1) Create the first two Anchor Points of your basic path;

2) Effect>Distort&Transform>Transform>ReflectX with 1 copy and the middle right side Reference Point chosen;

3) With the Pen Tool ClickDrag (or Click) anew from the second Anchor Point and go on;

If you wish, you may:

4) Object>Expand Appearance and Ctrl/Cmd+J to join the half paths.

Ctrl/Cmd+Z Undo is your friend: you can just go back and redo while drawing the basic path.

For multiple reflexion/rotation axes and plugins, you may have a look at solutions in this thread, including the links to external solutions below:

https://forums.adobe.com/thread/2284752

Or you can have a look at the MadPattern templates,

http://madpattern.com/

Or you can use the MirrorMe plugin from Atute Graphics,

http://www.astutegraphics.com/software/mirrorme/

[MissSparkles75]

Thanks so much Jacob, that is really great, I shall take a look and try them out. Excellent.

[Jacob Bugge]

You are welcome, Miss Sparkles.

I hope you will share your findings.

[SJRiegel]

Another way to guarantee a perfectly symmetrical shape is to draw one half of it, and then use the Transform Effect to reflect the other half. Any subsequent changes in the original half will be automatically applied to the reflection.

 

[rcraighead]

[favoxhille]

Do you know why i can only do this through scaling, and not with the direct selection as you've showed in the gif?

(i'm using Illustrator 2018)

nvm i just had to do a straight movement with the mouse as without guidelines i wasn't sure if it was going to lock by itself

[G_Man]

Wow - I can't believe I finally have the answer and it was so darn simple. Thank you!

[Jacob Bugge]

G, the Concurrent Handle Move thread lives, thanks to you.